###############################################################################

#

# EXAMPLE.conf:

#   An example configuration file for configuring the Net-SNMP agent ('snmpd')

#   See the 'snmpd.conf(5)' man page for details

#

#  Some entries are deliberately commented out, and will need to be explicitly activated

#

###############################################################################

#

#  AGENT BEHAVIOUR

#

#  Listen for connections from the local system only

#agentAddress  udp:127.0.0.1:161

#  Listen for connections on all interfaces (both IPv4 *and* IPv6)

agentAddress udp:161,udp6:[::1]:161

###############################################################################

#

#  SNMPv3 AUTHENTICATION

#

#  Note that these particular settings don't actually belong here.

#  They should be copied to the file /var/lib/snmp/snmpd.conf

#     and the passwords changed, before being uncommented in that file *only*.

#  Then restart the agent

  createUser authOnlyUser  MD5 "1212121212"

  createUser Zhukefeng2014  MD5 1212121212

#  createUser authPrivUser  SHA "remember to change this one too"  DES

#  createUser internalUser  MD5 "this is only ever used internally, but still change the password"

#  If you also change the usernames (which might be sensible),

#  then remember to update the other occurances in this example config file to match.

###############################################################################

#

#  ACCESS CONTROL

#

                                                 #  system + hrSystem groups only

view   systemonly  included   .1.3.6.1.2.1

view   systemonly  included   .1.3.6.1.2.1.25.1

                                                 #  Full access from the local host

rocommunity public  localhost

                                                 #  Default access to basic system info

#rocommunity public  default    -V systemonly

#以下为360云监控设置

rocommunity  Zhukefeng2014 default

                                                 #  Full access from an example network

                                                 #     Adjust this network address to match your local

                                                 #     settings, change the community string,

                                                 #     and check the 'agentAddress' setting above

#rocommunity secret  10.0.0.0/16

                                                 #  Full read-only access for SNMPv3

 rouser   authOnlyUser

 rouser   Zhukefeng2014 auth

                                                 #  Full write access for encrypted requests

                                                 #     Remember to activate the 'createUser' lines above

#rwuser   authPrivUser   priv

#  It's no longer typically necessary to use the full 'com2sec/group/access' configuration

#  r[ou]user and r[ow]community, together with suitable views, should cover most requirements

###############################################################################

#

#  SYSTEM INFORMATION

#

#  Note that setting these values here, results in the corresponding MIB objects being 'read-only'

#  See snmpd.conf(5) for more details

sysLocation    Sitting on the Dock of the Bay

sysContact     Me <me@example.org>

                                                 # Application + End-to-End layers

sysServices    72

#

#  Process Monitoring

#

                               # At least one  'mountd' process

proc  mountd

                               # No more than 4 'ntalkd' processes - 0 is OK

proc  ntalkd    4

                               # At least one 'sendmail' process, but no more than 10

proc  sendmail 10 1

#  Walk the UCD-SNMP-MIB::prTable to see the resulting output

#  Note that this table will be empty if there are no "proc" entries in the snmpd.conf file

#

#  Disk Monitoring

#

                               # 10MBs required on root disk, 5% free on /var, 10% free on all other disks

disk       /     10000

disk       /var  5%

includeAllDisks  10%

#  Walk the UCD-SNMP-MIB::dskTable to see the resulting output

#  Note that this table will be empty if there are no "disk" entries in the snmpd.conf file

#

#  System Load

#

                               # Unacceptable 1-, 5-, and 15-minute load averages

load   12 10 5

#  Walk the UCD-SNMP-MIB::laTable to see the resulting output

#  Note that this table *will* be populated, even without a "load" entry in the snmpd.conf file

###############################################################################

#

#  ACTIVE MONITORING

#

                                    #   send SNMPv1  traps

 trapsink     localhost public

                                    #   send SNMPv2c traps

#trap2sink    localhost public

                                    #   send SNMPv2c INFORMs

#informsink   localhost public

#  Note that you typically only want *one* of these three lines

#  Uncommenting two (or all three) will result in multiple copies of each notification.

#

#  Event MIB - automatically generate alerts

#

                                   # Remember to activate the 'createUser' lines above

iquerySecName   internalUser       

rouser          internalUser

                                   # generate traps on UCD error conditions

defaultMonitors          yes

                                   # generate traps on linkUp/Down

linkUpDownNotifications  yes

###############################################################################

#

#  EXTENDING THE AGENT

#

#

#  Arbitrary extension commands

#

 extend    test1   /bin/echo  Hello, world!

 extend-sh test2   echo Hello, world! ; echo Hi there ; exit 35

#extend-sh test3   /bin/sh /tmp/shtest

#  Note that this last entry requires the script '/tmp/shtest' to be created first,

#    containing the same three shell commands, before the line is uncommented

#  Walk the NET-SNMP-EXTEND-MIB tables (nsExtendConfigTable, nsExtendOutput1Table

#     and nsExtendOutput2Table) to see the resulting output

#  Note that the "extend" directive supercedes the previous "exec" and "sh" directives

#  However, walking the UCD-SNMP-MIB::extTable should still returns the same output,

#     as well as the fuller results in the above tables.

#

#  "Pass-through" MIB extension command

#

#pass .1.3.6.1.4.1.8072.2.255  /bin/sh       PREFIX/local/passtest

#pass .1.3.6.1.4.1.8072.2.255  /usr/bin/perl PREFIX/local/passtest.pl

# Note that this requires one of the two 'passtest' scripts to be installed first,

#    before the appropriate line is uncommented.

# These scripts can be found in the 'local' directory of the source distribution,

#     and are not installed automatically.

#  Walk the NET-SNMP-PASS-MIB::netSnmpPassExamples subtree to see the resulting output

#

#  AgentX Sub-agents

#

                                           #  Run as an AgentX master agent

 master          agentx

                                           #  Listen for network connections (from localhost)

                                           #    rather than the default named socket /var/agentx/master

#agentXSocket    tcp:localhost:705